Click to change the region

Application Notes

Working Priciple of Differential Pyroelectric Detectors

Working Principle of Differential Pyroelectric Detectors

Differential Pyroelectric Detector Differential Pyroelectric Detector

Unlike their thermopile cousins, pyro­electrics are still single-ended detectors; making them susceptible to electro­magnetic interference from non-detector related noise. Processor clocks, line interference, and other sources of electro­magnetic noise can still be coupled to their output causing unnecessary headaches during ­the design phases of new equipment.


LASER COMPONENTS not only has developed a new and unique pyroelectric connection method to ­eliminate electromagnetic interference, our new, patented 1 detector configurations (Fig.1 and Fig.4) improves the Signal to Noise ratio by approximately 1.4!


When charges are generated on the pyro­electric crystal, positive and negative charges are generated on opposite sides (Fig. 2). Both sides of the crystal produce opposing signals of equal magnitude, and by using our unique scheme we can subtract the signals from each other (using a differential or instrumentation amplifier) eliminating the common mode noise from outside sources, but effectively doubling the output!


Although our detector signal increases twofold, our noise increases by a factor of only √2; resulting in an overall signal to noise improvement of approximately 1.4. 


In Figure 3 we used one of our ­differential detectors and introduced common mode noise in the form of a 50 Hz signal. As you can see signal 1 and signal 2 both demonstrate the noise; whereas the mathematically subtracted output does not. As well as giving a significantly increased output, the common mode noise has been eliminated. 


Because this detector is also based on our Current Mode architecture, our ­differential detectors can be directly inputted in to modern ADCs and microcontrollers where this subtraction can be done in software; allowing you to cut out pre-amplification stages from your design, and cut down on development costs!

To top

Fig.1: Circuit diagram of our CM  based Differential Pyroelector Detector.

 

Fig.2: Demonstration of the effect on signal when both outputs are subtracted.

 

Fig.3: Common mode noise eliminated via differential detector.

 

1 Patent no.: US 10,302,500 B2 (May 28,2019)

Voltage Mode Differential Detector

Beyond Borders

The Voltage Mode Differential Detector is offered with a DLaTGS crystal pyroelectric element. The signals from the top and bottom of the crystal are each sent to the gate of a low noise JFET. The outputs from the source of the JFET’s need to be connected externally to the detector ground using (nominally) 47 kOhm resistors as shown in the Circuit Diagram. The two source output signals are of opposite polarity as is the case with the opamp outputs of the Current Mode Differential Detector Model LD2100. The two signals can be combined by subtraction, i.e., Final Output = Output 1 – Output 2. Since each of Output 1 and Output 2 are nominally equal in value (but 180 degrees out of phase) the Final Output is then double each output as with the LD2100.


The basic model for the Voltage Mode Differential Detector is the DD3151D1300 that is offered with a variety of IR windows for spectroscopic applications. The active DLaTGS element has a 1.3 mm diameter with absorbing metal black. For THz applications, the preferred detector is the DD3150D1300-p1, which detector has a nichrome metal electrode to absorb the incoming radiation, and a HDPE plastic window that is transparent at such long wavelengths. Other windows suitable for THz applications are polished, uncoated silicon and CVD diamond windows. The entire range of IR windows and filter windows available are listed and described in the Pyroelectric Detectors Filter and Window Selection Datasheet.  

 

Fig.4: Circuit Diagram and Connections of the VM based Differential Detector.

 

Fig.5: Bottom View of Detector Model DD3151D1300.

Team of experts
You have questions or need our support?
Please call us.
Uwe Asmus
Sales Account Manager / IR Components and Optical Filters
Uwe Asmus
LASER COMPONENTS Germany GmbH
82140 Olching
Contact Form
You would like to send us something? You can reach us by phone and by e-mail.

Laser Components

Werner-von-Siemens-Str. 15
82140 Olching
Deutschland

You will be redirected
to the Fiber Technology Website ...