Click to change the region

Technical Articles

Components for Measuring Breath Alcohol Content

Finding a suitable detector for a specific gas measurement still seems theoretically trivial. In order to measure the breath alcohol content (BrAC), the absorption lines of ethanol gas have to be analyzed. They are approximately 9.5 µm, 8.1 µm, 7.2 µm, and 3.4 µm. Theoretically, it would be sufficient to measure the detector signal at a single absorption line; however, it is important to make sure that a cross-sensitivity to other substances that are also in the breath (water, methane, and ethanol) does not exist.

Filter Selection

Beyond Borders

IR detectors are polychromatic. A suitable filter is required to detect a specific gas or measure a specific wavelength: Bandpass filters only allow the beams of a specific wavelength range to pass.
Thus, the success of the measurement always depends on the quality of the filter: the spectral width must line up precisely with the absorption line being measured, and the transmission of the filter should be as high as possible.
For BrAC measurements, analysis of the wavelengths 3.4 µm and 9.5 µm has become the standard.

Detector Selection

Beyond Borders

The shorter wavelength could be identified using different detector types: According to the overview, InAs, PbSe, cooled PbS and PbSe, and pyroelectric detectors are all suited for use.
Exclusive observation at 3.4 µm is critical, however, because the absorption lines of water vapor and methane gas are approximately equal.

The air in the breath contains moisture. In a worst-case scenario, it would not be possible to strictly separate ethanol and water vapor at 3.4 µm. As a greenhouse gas, methane can also be detected in the air; thus, the problem is the same.
Measurement at the wavelength of 9.5 µm is more significant, thus the selection of pyroelectric detectors is more likely.

The pyros can house up to four independent detector chips with an integrated bandpass filter in a single housing. One channel often serves as a reference, and the others are there for gas detection. The simultaneous measurement of a gas using two filters would be possible and is actually carried out as such in practice when a high dynamic range is required for measurement.

Finding a suitable detector for a specific gas measurement still seems theoretically trivial. In order to measure the breath alcohol content (BrAC), the absorption lines of ethanol gas have to be analyzed. They are approximately 9.5 µm, 8.1 µm, 7.2 µm, and 3.4 µm. Theoretically, it would be sufficient to measure the detector signal at a single absorption line; however, it is important to make sure that a cross-sensitivity to other substances that are also in the breath (water, methane, and ethanol) does not exist.

Filter Selection
IR detectors are polychromatic. A suitable filter is required to detect a specific gas or measure a specific wavelength: Bandpass filters only allow the beams of a specific wavelength range to pass.
Thus, the success of the measurement always depends on the quality of the filter: the spectral width must line up precisely with the absorption line being measured, and the transmission of the filter should be as high as possible.
For BrAC measurements, analysis of the wavelengths 3.4 µm and 9.5 µm has become the standard.

Detector Selection
The shorter wavelength could be identified using different detector types: According to the overview, InAs, PbSe, cooled PbS and PbSe, and pyroelectric detectors are all suited for use.
Exclusive observation at 3.4 µm is critical, however, because the absorption lines of water vapor and methane gas are approximately equal.

The air in the breath contains moisture. In a worst-case scenario, it would not be possible to strictly separate ethanol and water vapor at 3.4 µm. As a greenhouse gas, methane can also be detected in the air; thus, the problem is the same.
Measurement at the wavelength of 9.5 µm is more significant, thus the selection of pyroelectric detectors is more likely.

The pyros can house up to four independent detector chips with an integrated bandpass filter in a single housing. One channel often serves as a reference, and the others are there for gas detection. The simultaneous measurement of a gas using two filters would be possible and is actually carried out as such in practice when a high dynamic range is required for measurement.

LASER COMPONENTS Nordic - Your competent partner for optical and optoelectronic components in Sweden, Norway, Finland, Denmark, and Iceland.

Welcome to LASER COMPONENTS Nordic AB, your expert for photonics components. Each product in our wide range of detectors, laser diodes, laser modules, optics, fiber optics, and more is worth every Crown (SEK). Our customized solutions cover all conceivable areas of application: from sensor technology to medical technology. You can reach us here:

Box 14001 / Skårs led 3
SE-400 20 Göteborg
Sweden

Phone: +46 (0)31 703 7173
Email: info(at)lasercomponents.se

Team of experts
You have questions or need our support?
Please call us.
Harvey Washbrook
Sales Account Manager
Harvey Washbrook
Laser Components Nordic AB
41263 Göteborg - Sweden
Svante Karlsson
Sales Account Manager
Svante Karlsson
Laser Components Nordic AB
41263 Göteborg - Sweden
Contact Form
You would like to send us something? You can reach us by phone and by e-mail.

Laser Components

Box 14001 / Skårs led 3
SE-400 20 Göteborg
Sweden

Phone: +46 (0)31 703 7173

You will be redirected
to the Fiber Technology Website ...